It’s not that difficult to customize and install ceramic wall tile in your bathroom. A little patience and dedication will get you a long way when installing that dream ceramic tile bathroom wall you’ve always wanted to have.
Before you begin to install ceramic wall tile, get your tiling tools ceramic manufacturer together. You will need the following tools for this project: A tape measure, a tile cutter and a pair of tile nippers and a pair of pliers, tile spacers, sandpaper, a trowel (preferably notched) and a rubber grout float. To install ceramic wall tile on your bathroom walls properly, you will also need a strong setting material like tiling thinset mortar, or any of a wide selection of tile adhesives. You will also need tiling grout for filling in the gaps between your tiles. Make sure to match your setting material color with your grout.
A bucket, rags and sponges will also be needed for cleaning your tiles of excess grout and other debris, after you’re all done. And don’t start to install ceramic wall tile without these essentials: You will also need a pair of safety glasses, heavy leather gloves, and long-sleeved work clothes (broken shards, and other debris can cause nasty cuts, if you are not careful). Ready to start on your dream ceramic bathroom wall? Follow the tiling instructions below and make your ceramic tiled bathroom wall and start tiling!
You can begin by finding the center of your wall. Use a carpenter’s level, or long pieces of plumb to mark intersecting vertical and horizontal lines. These will be your reference lines for your tiling work. Where both lines intersect is the starting point for your first row of ceramic tiles. From that point, you may then be able to working your way to both ends of your bathroom wall. Make regular checks when you install ceramic wall tile, so that your tiling work is consistent and does run up or down in a slanting direction.
There are two types of bathroom walls you may be working on. One is the common concrete wall, and the other is a special type of called a green drywall. A green drywall is specifically designed for use in bathrooms and showers because it is designed to resist moisture intrusion. Be sure that you clean your walls of dust and debris, as well as repair cracks and fill in gaps and holes. Roughen up or scarify your wall so that your tiling mortar has some grip for bonding. That way, when you begin to install ceramic wall tile on your walls, you won’t have a problem with your tiling mortar or bonding material.
You may now start installing ceramic wall tile once the walls are laid out. Start at your reference lines’ intersection point. Apply a coat of tiling thinset mortar. Place your tile over it and press the tile down firmly in place. Give it a twisting motion to set it in place. Stop pressing when you feel your tile has set and is no longer wobbly. Duplicate this procedure with the rest of your ceramic tiles. To get a consistent tiling, place tile spacers on all the spaces between your ceramic bathroom tiles. Don’t forget to check your work every now and then.
You may not need to use the entire tile as you finish up the end of the row. Use a tile cutter to get your tile under the right size. Then, smoothen the cut edge with sandpaper. Be careful: The edge of a cut ceramic bathroom tile is very sharp. For irregular, use your tile nippers. First draw an outline of the irregular and etch a line along it. Then, use your tile nipper to break off the unusable edges, until you have required shape. Do this a little at a time, so you can control your tile nipping. Don’t forget to sand the edges over.
Once you’re done tiling the bathroom wall, leave it to set, overnight, at the very least, or twenty-four hours, at the most. After this setting period, it’s time to lay in your grout. There are two main kinds of grout: Sanded or unsanded grout. Sanded grout is a mixture of cement, water and fine sand. Unsanded grout is any of a wide selection of polymer-based and epoxy resin adhesive grout used to install ceramic wall tile. If your tile spaces are more than an eighth of an inch wide, use sanded grout. For smaller tile spaces, use unsanded grout. Start by map out your bathroom wall and work one section at a time. To maximize your grout application, angle your rubber grout float and press down firmly as you spread it over the tile spaces. Check for pockets of air. Dab these spaces with more grout lining by using the edges of your grout float. Use a damp sponge to wipe off any excess grout. Rinse your sponge regularly so you can get a cleaner and better finish. Let your grout dry for a day and then take a dry piece of cloth and clean and buff your tiles.